Description
DuPont™ IntegraTec™ XP77IG Modules for Open Platform (previously DuPont™ IntegraFlux™ SFP-2880XP)
Key Features:
– Proven XP™ Hydrophilic PVDF Fiber:
– Superior fouling and chlorine resistance.
– High colloidal particulate, bacteria, and virus log removal rate.
– Excellent filtration permeability.
– Easy cleaning and wettability.
– Optimized Module Design:
– Open platform design to adapt with customer built skids.
– High active filtration area to maximize productivity.
– High operation recovery with high air scouring tolerance.
– Reduced chemical consumption with maintenance cleanings protocol.
– Robust materials for long lifetime.
– Easy installation and low maintenance.
Key Applications:
– High recovery and large size filtration in:
– Industrial utility water.
– Industrial wastewater reuse.
– Municipal wastewater filtration.
– RO pretreatment.
Module Specification:
General:
– Mode of Filtration: Out-In Pressurized
– Membrane Type: Hollow fiber
– Membrane Material: PVDF (Polyvinylidene Fluoride)
– Membrane Pore Size: 0.03 μm
– Module Operating Process: Dead-end
– Other Wetted Module Components: Polyurethane, uPVC, EPDM, and ABS
Dimensions:
– Active Membrane Area: 77 m² (829 ft²)
– Module Length Overall (L): 2,360 ± 3.0 mm (92.9 ± 0.1 inch)
– Module Length (L3): 2,320 ± 3.0 mm (91.3 ± 0.1 inch)
– Module Length (L2): 2,130 ± 3.0 mm (83.9 ± 0.1 inch)
– Module Length (L1): 2,000 ± 3.0 mm (78.7 ± 0.1 inch)
– Module Diameter (D): 225 mm (8.9 inch)
– Module Width (W1): 180 mm (7.1 inch)
– Module Width (W2): 342 mm (13.5 inch)
– Feed/Filtrate port DN50 (F): 51 mm (2.0 inch)
Weight and Volume:
– Shipping Weight: 73 kg (161 lbs)
– Weight Empty: 61 kg (134 lbs)
– Weight Filled: 100 kg (220 lbs)
– Hold-Up Volume Feed (Clean-In-Place = CIP): 37 L (9.8 gal)
– Hold-Up Volume Membrane Structure (CIP): 14 L (3.7 gal)
– Hold-Up Volume Filtrate (CIP): 10 L (2.6 gal)
Part No / GMID: 12091621
Suggested Operating Conditions:
General Details:
– Operating Temperature Range: 1-40°C (34-104°F)
– Operating pH: 2-11
– Cleaning pH: 2-12
– Typical Filtration Trans-Membrane Pressure (TMP): 0.4-1.5 bar (5.8-21.8 psi)
– Typical Backwash TMP: 0.6-2.0 bar (8.7-29.0 psi)
– Backwash Type: Air scour with liquid backwash
– Backwash Flux: 100 L/(m²h) (58.8 gfd)
– Backwash Flow: 7.7 m³/h (34.0 gpm)
Operating Limits (Maximum):
– Rate of Pressure Change: 0.5 bar/sec (7.3 psi/sec)
– Inlet Pressure: 6.25 bar (at 20 °C) (90.7 psi)
– Filtration TMP: 2.1 bar (30.5 psi)
– Backwash TMP: 2.5 bar (36 psi)
– Filtration Flux: 110 L/(m²h) (64.5 gfd)
– Filtration Flow: 8.5 m³/h (37.4 gpm)
– Backwash Flux: 120 L/(m²h) (70.6 gfd)
– Particle Size: 300 μm
– Exposure NaOCl: ≤1,500,000 ppmxh
– Recommended max. instantaneous exposure NaOCl: 2,000 ppm
General Information:
– Avoid any abrupt pressure variations during start-up, operation, shutdown, cleaning or other sequences to prevent possible membrane damage. The maximum pressure change allowable is 0.5 bar/s.
– For assembly, please refer to the latest version of the DuPont™ IntegraTec™ PVDF-UF Out-In P Series Modules for Open Platforms Assembly Manual (Form No. 45-D02507-en).
– If operating limits and guidelines given in this document are not strictly followed, any warranty will be null and void.
– To control biological growth during extended system shutdowns, storage solution has to be introduced into the membrane modules.
Regulatory Note:
– Certified drinking water modules require specific conditioning procedures prior to producing potable water. For operating parameters, please refer to the DuPont™ IntegraTec™ P Series PVDF-UF Out-In Process and Design Manual (Form No. 45-D00874-en).
– Drinking water modules may be subjected to additional regulatory restrictions in some countries. Please check local regulatory guidelines and application status before use.
– Flushing needs to be done according to the DuPont™ IntegraTec™ PVDF-UF Out-In P Series Modules for Open Platforms Assembly Manual (Form No. 45-D02507-en).
