Hydranautics Membranes – Aqua Components https://aquacomponents.sa Reliable Water Solutions for Saudi Arabia Thu, 13 Mar 2025 12:54:59 +0000 en-US hourly 1 https://wordpress.org/?v=6.9.4

Hydranautics PRO-XT2 Membrane https://aquacomponents.sa/product/hydranautics-pro-xt2-membrane/ Thu, 13 Mar 2025 12:54:58 +0000 https://aquacomponents.sa/product/hydranautics-pro-xt2-membrane/ The Hydranautics® PRO-XT2 element series is a set of ultra high-pressure spiral wound membranes customized specifically for challenging industrial process applications such as brine dewatering. These membranes are based on existing Hydranautics high performance membrane products which have been specially designed to treat a variety of industrial feed streams including high fouling, high TDS, or chemically aggressive feeds.

Models

Specified Performance

  • Permeate Flow (at initial test): 8,000 gpd (30.3 m3/d)
  • Salt Rejection: 99.8% (99.7% minimum)
  • Test Conditions: 32000 ppm NaCl solution
    – 800 psig (5.5 MPa) Applied Pressure
    – 77 °F (25 °C) Operating Temperature
    – 10% Permeate Recovery
    – 6.5 – 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified. Expect as much as 25% flux loss after operating near high pressure limits.

General Product Description

  • Configuration: Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Membrane Active Area**: 330 ft2 (30.7 m2)
  • Feed Spacer: 34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box

Element Details**

A, Inches (mm) B, Inches (mm) C, Inches (mm)
40.0 (1016) 7.89 (200) 1.125 (28.6)

**Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions

  • Maximum Applied Pressure: 1800 psig (124 bar) up to 30°C (see Chart 1 for detail)
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2-11 (1-13)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow: 85 gpm (19.3 m3/h)
  • Minimum Brine Flow: 12 gpm (2.7 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi (0.10 MPa)

Note: The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane.

Table 1: Maximum pressure vs temperature

Max pressure Vs Temperature limits for

PRO-XP elements

Max Pressure VS Temperature Limits for PRO-XP Elements
°F °C psi bar
33.8 1 1800 124.1
50 10 1800 124.1
68 20 1800 124.1
86 30 1800 124.1
95 35 1575 108.6
104 40 1325 91.4
113 45 1100 75.8

Features

  • Complements BWRO and SWRO by further increasing the solute concentration
  • Reduces CAPEX and OPEX by downsizing the evaporator by reducing brine volume
  • Increases the overall efficiency of ZLD / MLD systems
  • Cost-effective, innovative, and sustainable
Applications
  • Brine dewatering
  • Municipal wastewater
  • Landfill and leachates
  • Pharmaceutical
  • Mining water treatment
  • Textile Industries
  • Power & energy
]]> Hydranautics PRO-LF1 Membrane https://aquacomponents.sa/product/hydranautics-pro-lf1-membrane/ Thu, 13 Mar 2025 12:54:54 +0000 https://aquacomponents.sa/product/hydranautics-pro-lf1-membrane/ The Hydranautics® PRO-LF1 element series is a set of ultra high-pressure spiral wound membranes customized specifically for challenging industrial process applications such as brine dewatering. These membranes are based on existing Hydranautics high performance membrane products which have been specially designed to treat a variety of industrial feed streams including high fouling, high TDS, or chemically aggressive feeds.

Models

Specified Performance

  • Permeate Flow (at initial test): 8,000 gpd (30.3 m3/d)
  • Salt Rejection: 99.8% (99.7% minimum)
  • Test Conditions: 32000 ppm NaCl solution
    – 800 psig (5.5 MPa) Applied Pressure
    – 77 °F (25 °C) Operating Temperature
    – 10% Permeate Recovery
    – 6.5 – 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified. Expect as much as 25% flux loss after operating near high pressure limits.

General Product Description

  • Configuration: Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Membrane Active Area**: 330 ft2 (30.7 m2)
  • Feed Spacer: 34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box

Element Details**

A, Inches (mm) B, Inches (mm) C, Inches (mm)
40.0 (1016) 7.89 (200) 1.125 (28.6)

**Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions

  • Maximum Applied Pressure: 1800 psig (124 bar) up to 30°C (see Chart 1 for detail)
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2-11 (1-13)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow: 85 gpm (19.3 m3/h)
  • Minimum Brine Flow: 12 gpm (2.7 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi (0.10 MPa)

Note: The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane.

Table 1: Maximum pressure vs temperature

Max pressure Vs Temperature limits for

PRO-XP elements

Max Pressure VS Temperature Limits for PRO-XP Elements
°F °C psi bar
33.8 1 1800 124.1
50 10 1800 124.1
68 20 1800 124.1
86 30 1800 124.1
95 35 1575 108.6
104 40 1325 91.4
113 45 1100 75.8

Features

  • Complements BWRO and SWRO by further increasing the solute concentration
  • Reduces CAPEX and OPEX by downsizing the evaporator by reducing brine volume
  • Increases the overall efficiency of ZLD / MLD systems
  • Cost-effective, innovative, and sustainable
Applications
  • Brine dewatering
  • Municipal wastewater
  • Landfill and leachates
  • Pharmaceutical
  • Mining water treatment
  • Textile Industries
  • Power & energy
]]> Hydranautics PRO-XS3 Membrane https://aquacomponents.sa/product/hydranautics-pro-xs3-membrane/ Thu, 13 Mar 2025 12:54:51 +0000 https://aquacomponents.sa/product/hydranautics-pro-xs3-membrane/ The Hydranautics® PRO-XS3 element series is a set of ultra high-pressure spiral wound membranes customized specifically for challenging industrial process applications such as brine dewatering. These membranes are based on existing Hydranautics high performance membrane products which have been specially designed to treat a variety of industrial feed streams including high fouling, high TDS, or chemically aggressive feeds.

Models

Specified Performance

  • Permeate Flow (at initial test): 8,000 gpd (30.3 m3/d)
  • Salt Rejection: 99.8% (99.7% minimum)
  • Test Conditions: 32000 ppm NaCl solution
    – 800 psig (5.5 MPa) Applied Pressure
    – 77 °F (25 °C) Operating Temperature
    – 10% Permeate Recovery
    – 6.5 – 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified. Expect as much as 25% flux loss after operating near high pressure limits.

General Product Description

  • Configuration: Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Membrane Active Area**: 330 ft2 (30.7 m2)
  • Feed Spacer: 34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box

Element Details**

A, Inches (mm) B, Inches (mm) C, Inches (mm)
40.0 (1016) 7.89 (200) 1.125 (28.6)

**Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions

  • Maximum Applied Pressure: 1800 psig (124 bar) up to 30°C (see Chart 1 for detail)
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2-11 (1-13)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow: 85 gpm (19.3 m3/h)
  • Minimum Brine Flow: 12 gpm (2.7 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi (0.10 MPa)

Note: The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane.

Table 1: Maximum pressure vs temperature

Max pressure Vs Temperature limits for

PRO-XP elements

Max Pressure VS Temperature Limits for PRO-XP Elements
°F °C psi bar
33.8 1 1800 124.1
50 10 1800 124.1
68 20 1800 124.1
86 30 1800 124.1
95 35 1575 108.6
104 40 1325 91.4
113 45 1100 75.8

Features

  • Complements BWRO and SWRO by further increasing the solute concentration
  • Reduces CAPEX and OPEX by downsizing the evaporator by reducing brine volume
  • Increases the overall efficiency of ZLD / MLD systems
  • Cost-effective, innovative, and sustainable
Applications
  • Brine dewatering
  • Municipal wastewater
  • Landfill and leachates
  • Pharmaceutical
  • Mining water treatment
  • Textile Industries
  • Power & energy
]]> Hydranautics PRO-XS2 Membrane https://aquacomponents.sa/product/hydranautics-pro-xs2-membrane/ Thu, 13 Mar 2025 12:54:47 +0000 https://aquacomponents.sa/product/hydranautics-pro-xs2-membrane/ The Hydranautics® PRO-XS2 element series is a set of ultra high-pressure spiral wound membranes customized specifically for challenging industrial process applications such as brine dewatering. These membranes are based on existing Hydranautics high performance membrane products which have been specially designed to treat a variety of industrial feed streams including high fouling, high TDS, or chemically aggressive feeds.

Models

Specified Performance

  • Permeate Flow (at initial test): 8,000 gpd (30.3 m3/d)
  • Salt Rejection: 99.8% (99.7% minimum)
  • Test Conditions: 32000 ppm NaCl solution
    – 800 psig (5.5 MPa) Applied Pressure
    – 77 °F (25 °C) Operating Temperature
    – 10% Permeate Recovery
    – 6.5 – 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified. Expect as much as 25% flux loss after operating near high pressure limits.

General Product Description

  • Configuration: Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Membrane Active Area**: 330 ft2 (30.7 m2)
  • Feed Spacer: 34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box

Element Details**

A, Inches (mm) B, Inches (mm) C, Inches (mm)
40.0 (1016) 7.89 (200) 1.125 (28.6)

**Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions

  • Maximum Applied Pressure: 1800 psig (124 bar) up to 30°C (see Chart 1 for detail)
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2-11 (1-13)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow: 85 gpm (19.3 m3/h)
  • Minimum Brine Flow: 12 gpm (2.7 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi (0.10 MPa)

Note: The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane.

Table 1: Maximum pressure vs temperature

Max pressure Vs Temperature limits for

PRO-XP elements

Max Pressure VS Temperature Limits for PRO-XP Elements
°F °C psi bar
33.8 1 1800 124.1
50 10 1800 124.1
68 20 1800 124.1
86 30 1800 124.1
95 35 1575 108.6
104 40 1325 91.4
113 45 1100 75.8

Features

  • Complements BWRO and SWRO by further increasing the solute concentration
  • Reduces CAPEX and OPEX by downsizing the evaporator by reducing brine volume
  • Increases the overall efficiency of ZLD / MLD systems
  • Cost-effective, innovative, and sustainable
Applications
  • Brine dewatering
  • Municipal wastewater
  • Landfill and leachates
  • Pharmaceutical
  • Mining water treatment
  • Textile Industries
  • Power & energy
]]> Hydranautics PRO-XS1 Membrane https://aquacomponents.sa/product/hydranautics-pro-xs1-membrane/ Thu, 13 Mar 2025 12:54:44 +0000 https://aquacomponents.sa/product/hydranautics-pro-xs1-membrane/ The Hydranautics® PRO-XS element series is a set of ultra high-pressure spiral wound membranes customized specifically for challenging industrial process applications such as brine dewatering. These membranes are based on existing Hydranautics high performance membrane products which have been specially designed to treat a variety of industrial feed streams including high fouling, high TDS, or chemically aggressive feeds.

Models

Specified Performance

  • Permeate Flow (at initial test): 8,000 gpd (30.3 m3/d)
  • Salt Rejection: 99.8% (99.7% minimum)
  • Test Conditions: 32000 ppm NaCl solution
    – 800 psig (5.5 MPa) Applied Pressure
    – 77 °F (25 °C) Operating Temperature
    – 10% Permeate Recovery
    – 6.5 – 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified. Expect as much as 25% flux loss after operating near high pressure limits.

General Product Description

  • Configuration: Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Membrane Active Area**: 330 ft2 (30.7 m2)
  • Feed Spacer: 34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box

Element Details**

A, Inches (mm) B, Inches (mm) C, Inches (mm)
40.0 (1016) 7.89 (200) 1.125 (28.6)

**Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions

  • Maximum Applied Pressure: 1800 psig (124 bar) up to 30°C (see Chart 1 for detail)
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2-11 (1-13)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow: 85 gpm (19.3 m3/h)
  • Minimum Brine Flow: 12 gpm (2.7 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi (0.10 MPa)

Note: The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane.

Table 1: Maximum pressure vs temperature

Max pressure Vs Temperature limits for

PRO-XP elements

Max Pressure VS Temperature Limits for PRO-XP Elements
°F °C psi bar
33.8 1 1800 124.1
50 10 1800 124.1
68 20 1800 124.1
86 30 1800 124.1
95 35 1575 108.6
104 40 1325 91.4
113 45 1100 75.8

Features

  • Complements BWRO and SWRO by further increasing the solute concentration
  • Reduces CAPEX and OPEX by downsizing the evaporator by reducing brine volume
  • Increases the overall efficiency of ZLD / MLD systems
  • Cost-effective, innovative, and sustainable
Applications
  • Brine dewatering
  • Municipal wastewater
  • Landfill and leachates
  • Pharmaceutical
  • Mining water treatment
  • Textile Industries
  • Power & energy
]]> Hydranautics PRO-XR1 Membrane https://aquacomponents.sa/product/hydranautics-pro-xr1-membrane/ Thu, 13 Mar 2025 12:54:39 +0000 https://aquacomponents.sa/product/hydranautics-pro-xr1-membrane/ The Hydranautics® PRO-XP element series is a set of ultra high-pressure spiral wound membranes customized specifically for challenging industrial process applications such as brine dewatering. These membranes are based on existing Hydranautics high performance membrane products which have been specially designed to treat a variety of industrial feed streams including high fouling, high TDS, or chemically aggressive feeds.

Models

Specified Performance

  • Permeate Flow (at initial test): 8,000 gpd (30.3 m3/d)
  • Salt Rejection: 99.8% (99.7% minimum)
  • Test Conditions: 32000 ppm NaCl solution
    – 800 psig (5.5 MPa) Applied Pressure
    – 77 °F (25 °C) Operating Temperature
    – 10% Permeate Recovery
    – 6.5 – 7.0 pH Range

*The Specified Performance is based on data taken after a minimum of 10 minutes of operation. Actual testing of elements may be done at conditions which vary from these exact values; in which case, the performance is normalized back to these standard conditions. Permeate flow for individual elements may vary ±15 percent from the value specified. Expect as much as 25% flux loss after operating near high pressure limits.

General Product Description

  • Configuration: Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Membrane Active Area**: 330 ft2 (30.7 m2)
  • Feed Spacer: 34 mil (0.86 mm)

Packaging: All membrane elements are supplied with a brine seal, interconnector, and O-rings. Elements are enclosed in a sealed polyethylene bag containing less than 1.0% sodium meta-bisulfite solution, and then packaged in a cardboard box

Element Details**

A, Inches (mm) B, Inches (mm) C, Inches (mm)
40.0 (1016) 7.89 (200) 1.125 (28.6)

**Values listed are indicative, not specified. For more detailed specifications, see our Technical Service Bulletin documents or contact Hydranautics Technical Department.

Product Use and Restrictions

  • Maximum Applied Pressure: 1800 psig (124 bar) up to 30°C (see Chart 1 for detail)
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2-11 (1-13)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow: 85 gpm (19.3 m3/h)
  • Minimum Brine Flow: 12 gpm (2.7 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi (0.10 MPa)

Note: The limitations shown here are for general use. For specified projects, operation at more conservative values may ensure the best performance and longest life of the membrane.

Table 1: Maximum pressure vs temperature

Max pressure Vs Temperature limits for

PRO-XP elements

Max Pressure VS Temperature Limits for PRO-XP Elements
°F °C psi bar
33.8 1 1800 124.1
50 10 1800 124.1
68 20 1800 124.1
86 30 1800 124.1
95 35 1575 108.6
104 40 1325 91.4
113 45 1100 75.8

Features

  • Complements BWRO and SWRO by further increasing the solute concentration
  • Reduces CAPEX and OPEX by downsizing the evaporator by reducing brine volume
  • Increases the overall efficiency of ZLD / MLD systems
  • Cost-effective, innovative, and sustainable
Applications
  • Brine dewatering
  • Municipal wastewater
  • Landfill and leachates
  • Pharmaceutical
  • Mining water treatment
  • Textile Industries
  • Power & energy
]]> Hydranautics HydraPRO 513 Membrane https://aquacomponents.sa/product/hydranautics-hydrapro-513-membrane/ Thu, 13 Mar 2025 12:48:53 +0000 https://aquacomponents.sa/product/hydranautics-hydrapro-513-membrane/ The HydraPRO 513 Membrane is designed by Hydraunatics to provide users with a custom-made element exceptionally effective in removing color and other unwanted substances such as dissolved solids and salts from water. This process ensures the highest quality of water produced, and is further productively enacted with built-in features that make the membrane 100% resistant to chlorine.

Models

Type
  • Configuration: Low Fouling Spiral Wound
  • Membrane Polymer: Composite Polyamide

Features

Standar Operationg Limits
  • Maximum Applied Pressure:600 psig (4.1 MPa) at 65 °C
  • (see Chart 1 for detail): 200 psig (1.4 MPa) at 90 °C
  • Maximum Chlorine Concentration: < 0.1 ppm
  • pH Range, Continuous (Cleaning): 2 –11 (1 –13)*
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow for 2540: 16 gpm 6 gpm (23 l/m)
  • Maximum Feed Flow for 4040: (3.6 m³/h)
  • Maximum Feed Flow for 8040: 75 gpm (17 m³/h)
  • Maximum Pressure Drop for Each Element: 15 psi 

Applications

  • Removal of color and large molecular weight organics from feedwater.
  • Industrial, food and beverage, and municipal feedwaters.

Docs
HydraPRO 500 series membrane elements areincorporated with features to provide maximum flow rate and extremely high rejection. There is a brine seal, or-rings, and interconnector accompanied to further imrpove performance. All elements come in 4 and 8 inch sizes.
Hydranautics HydraPRO 513 Membrane Data Sheet

]]> Hydranautics HydraPRO 502 Membrane https://aquacomponents.sa/product/hydranautics-hydrapro-502-membrane/ Thu, 13 Mar 2025 12:48:52 +0000 https://aquacomponents.sa/product/hydranautics-hydrapro-502-membrane/ The HydraPRO 502 Membrane is a color removal membrane manufactured by Hydranautics with spiral-would and crossflow elements that improve the purity of water through eliminating dissoved salts and color. These membranes are made to me more effective by being resistant to chlorine.

Models

Type
  • Configuration: Low Fouling Spiral Wound
  • Membrane Polymer: Composite Polyamide

Features

Standar Operating Limits:
  • Maximum Applied Pressure:600 psig (4.1 MPa) at 65 °C
  • (see Chart 1 for detail): 200 psig (1.4 MPa) at 90 °C
  • Maximum Chlorine Concentration: < 0.1 ppm
  • pH Range, Continuous (Cleaning): 2 –11 (1 –13)*
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow for 2540: 16 gpm 6 gpm (23 l/m)
  • Maximum Feed Flow for 4040: (3.6 m3/h)
  • Maximum Feed Flow for 8040: 75 gpm (17 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi 

Applications

  • Removal of color and large molecular weight organics from feedwater.
  • Industrial, food and beverage, and municipal feedwaters.

]]> Hydranautics HydraPRO 501 Membrane https://aquacomponents.sa/product/hydranautics-hydrapro-501-membrane/ Thu, 13 Mar 2025 12:48:50 +0000 https://aquacomponents.sa/product/hydranautics-hydrapro-501-membrane/ The HydraPRO 501 Membrane is apart of Hydranuatics 500 series that consist of spiral wound membrane elements specifically designed for industrial process applications. These membranes work to treat product water that posess issues such as high temperature, significant fouling, and hazardous chemicals. 

Models

Type
  • Configuration: Low Fouling Spiral Wound
  • Membrane Polymer: Composite Polyamide

Features

Standard Operating Limits:
  • Maximum Applied Pressure:600 psig (4.1 MPa) at 65 °C
  • (see Chart 1 for detail): 200 psig (1.4 MPa) at 90 °C
  • Maximum Chlorine Concentration: < 0.1 ppm
  • Maximum Operating Temperature: Pressure dependent (see Chart 1 for detail)
  • pH Range, Continuous (Cleaning): 2 –11 (1 –13)*
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow for 2540: 16 gpm 6 gpm (23 l/m)
  • Maximum Feed Flow for 4040: (3.6 m3/h)
  • Maximum Feed Flow for 8040: 75 gpm (17 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi 

Applications

  • Removal of color and large molecular weight organics from feedwater.
  • Industrial, food and beverage, and municipal feedwaters.

]]> Hydranautics HydraPRO 421 Membrane https://aquacomponents.sa/product/hydranautics-hydrapro-421-membrane/ Thu, 13 Mar 2025 12:48:49 +0000 https://aquacomponents.sa/product/hydranautics-hydrapro-421-membrane/ Hydranautics HydraPRO 421 Membrane is a specialized element manufactured by Hydranautics that provides high quality performance to a wide range of industrial process applications that includes high degrees of fouling and salinity. 

Models

Specifications

Model

Feed Spacer inch (cm)

Area, ft2 (m2)

Permeate Flow

SO4 Rej.% (avg)

HYDRApro 421-8040

34

400

 
11000 gpd (41.6 m³/d)

99.7%

Features

Standard Operating Limits:
  • Configuration: Low Fouling Spiral Wound
  • Membrane Polymer: Composite Polyamide
  • Maximum Applied Pressure: 600 psig (4.1 MPa) for HYDRApro 402
  • Maximum Applied Pressure: 1200 psig (8.3 MPa) for HYDRApro 421
  • Maximum Chlorine Concentration: < 0.1 PPM
  • Maximum Operating Temperature: 113 °F (45 °C)
  • pH Range, Continuous (Cleaning): 3.0 – 9.0 (1.0 – 11.5)
  • Maximum Feedwater Turbidity: 1.0 NTU
  • Maximum Feedwater SDI (15 mins): 5.0
  • Maximum Feed Flow for 4040: 16 GPM (3.6 m3/h)
  • Maximum Feed Flow for 8040: 85 GPM (19.30 m3/h)
  • Maximum Pressure Drop for Each Element: 15 psi

Applications

  • Removal of color and large molecular weight organics from feedwater.
  • Industrial, food and beverage, and municipal feedwaters.

]]>